The author is making a few good pointers on Installing A Bathtub as a whole in this post on the next paragraphs.
Mounting a tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the brand-new one. See to it you have actually qualified yourself for the work and are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about using one prior to you begin. Opportunities are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and don't need to change the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will certainly come from the pipes. Once the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait till the tub has actually been used a minimum of when as this will resolve it right into its final setting.
Planning for the Setup
To start with, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, bring about complications with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about Tools You Need to Install a New Bathtub ? Put a remark directly below. We'd be interested to listen to your reactions about this blog post. We hope that you come back again in the near future. Remember to take a moment to share this blog post if you enjoyed it. I praise you for your time. Please check our website back soon.
Book Instantly